Space-ray RSTP Series User Manual

Form 43206000 Sept 2011 INSTALLATION AND OPERATION INSTRUCTIONS OWNER / INSTALLER: For your safety this manual must be carefully and thoroughly

Form 43206000 Sept 2011 -9- d.EyeboltTurnbuckle*MinimumNo. 2 Chain*Eyeboltc.ThreadedRodTurnbuckleEyeboltb.3/16 x 1 wideFlat BarMinimumNo. 2 Chain*a

Form 43206000 -10- Sept 2011 10.0) HEATER ASSEMBLY Sheet metal parts, particularly reflectors and vent have sharpedges. Always use gloves when handl

Form 43206000 Sept 2011 -11- 2. Install the suspension chains (according to Section 7.0) using proper suspension method (see Section 9.0). chains fo

Form 43206000 -12- Sept 2011 NOTE:NOTE:NOTE:NOTE: EXHAUST HOODS ANDEXHAUST HOODS ANDEXHAUST HOODS ANDEXHAUST HOODS AND INLET AIR HOODS

Form 43206000 Sept 2011 -13- 11.0) GAS CONNECTIONS AND REGULATIONS Tighten flexible gas hose and components securely.Flexible metal gas hoses must b

Form 43206000 -14- Sept 2011 KEY DIMENSIONS AND COMPONENTS OF THE GAS CONNECTIONSEND VIEWGas Pressure= 2 PSIGGas SupplyPipingSediment Trap(Drip Leg)*

Form 43206000 Sept 2011 -15- 12.0) INSTRUCTIONS FOR PRESSURE TEST GAUGE CONNECTION Failure to do so may result in death, serious injury or propertyd

Form 43206000 -16- Sept 2011 13.0) ELECTRICAL CONNECTIONS Failure to do so may result in death or serious injury.This appliance must be connected to

Form 43206000 Sept 2011 -17- SCHEMATICSCHEMATICSCHEMATICSCHEMATIC WIRING DIAGRAM WIRING DIAGRAM WIRING DIAGRAM WIRING DIAGRAM ———— Direct

Form 43206000 -18- Sept 2011 C.C.C.C. LOWLOWLOWLOW VOLTAGE (VOLTAGE (VOLTAGE (VOLTAGE (24242424V) THERMOSTAT CONNECTIONS V) THERMOSTAT CONNEC

Form 43206000 Sept 2011 -1- TABLE OF CONTENTS SECTION DESCRIPTION PAGE 1.0) Safety ...

Form 43206000 Sept 2011 -19- 14.0) VENTING Failure to do so may result in death, serious injury, property damage or illnessfrom Carbon Monoxide pois

Form 43206000 -20- Sept 2011 Total VentHeight5 ft (152cm)minimum6 DiameterVent ConnectorTotal VentHeight1/4(6mm)per ft riseLateralSingle Heater Ven

Form 43206000 Sept 2011 -21- MULTIPLE HEATER VENTING (CONNECTIONS INTO A COMMON VENT OR MANIFOLD)MULTIPLE HEATER VENTING (CONNECTIONS INTO

Form 43206000 -22- Sept 2011 Multiple Heater Horizontal Venting Arrangement 6 diametersingle wall ventPlan ViewVent Cap2 (5cm)ClearanceThimble6

Form 43206000 Sept 2011 -23- B.B.B.B. INDIRECT VENTING (UNVENTED HEINDIRECT VENTING (UNVENTED HEINDIRECT VENTING (UNVENTED HEINDIRECT VENTI

Form 43206000 -24- Sept 2011 Flue vent terminationmust be 1 ft. (30cm)higher than combustionair inlet capPerforated Cover(Remove)Control BoxThe combu

Form 43206000 Sept 2011 -25- To bring outside combustion air to the heater, you will need to order the RSTP Fresh Air Kit (Part #427820RSTP Fresh Air

Form 43206000 -26- Sept 2011 16.0) LIGHTING AND SHUTDOWN INSTRUCTIONS Failure to do so may result in death, serious injury or propertydamage.The acc

Form 43206000 Sept 2011 -27- 18.0) CONTROL COMPONENT LOCATION 1 Cabinet Assembly2 Air Inlet Plate3 Access Panel4 Sight Glass5 Flame Sensor6 Ignition

Form 43206000 -28- Sept 2011 19.0) CLEANING AND ANNUAL MAINTENANCE ELECTRIC SHOCK & EXPLOSION HAZARDDisconnect electrical power and gas supply b

Form 43206000 -2- Sept 2011 1.0) SAFETY This heater is a self-contained infrared radiant tube heater. Safety information required during installat

Form 43206000 Sept 2011 -29- 20.0) TROUBLESHOOTING GUIDE Turn on line voltageand thermostat. Doesthe green monitoringlight come on in thecontrol ca

Form 43206000 -30- Sept 2011 30 seconds afterstartup, does theamber monitoring lightcome on in the controlcabinet?YesNowhile the amber lightis on

Form 43206000 Sept 2011 -31- Call for heat ends andthe heater shuts off?YesNoTroubleshooting ends.Thermostat is notworking properly.Replace it i

Form 43206000 -32- Sept 2011 21.0) REPLACING PARTS ELECTRIC SHOCK & EXPLOSION HAZARDDisconnect electrical power and gas supply beforeservicing.F

Form 43206000 Sept 2011 -33- 21.2) REMOVING MAIN BURNER AND GAS VALVE 345612 1. Disconnect electrical supply and gas connection from control box.

Form 43206000 -34- Sept 2011 21.4) IGNITION SYSTEM CHECKS TO CHECK TO CHECK TO CHECK TO CHECK IGNITION CABLEIGNITION CABLEIGNITION CABLEIGNITION CAB

Form 43206000 Sept 2011 -35- VALVEVALVE(GND)25V (GND)25VXModuleMultipurposeMeterRed (+)Black (-)FLAME SENSOR CURRENT CHECK- use microamp scale - 2

Form 43206000 -36- Sept 2011 23.0) REPLACEMENT PARTS GUIDE CONTROL COMPONENTSCONTROL COMPONENTSCONTROL COMPONENTSCONTROL COMPONENTS Item No.Item

Form 43206000 Sept 2011 -37- CONTROL COMPONENTSCONTROL COMPONENTSCONTROL COMPONENTSCONTROL COMPONENTS Item No.Item No.Item No.Item No. Part No.

Form 43206000 -38- Sept 2011 BODYBODYBODYBODY COMPONENTSCOMPONENTSCOMPONENTSCOMPONENTS Item No.Item No.Item No.Item No. Part No.Part No.Par

Form 43206000 Sept 2011 -3- The heater, when installed in aircraft hangars and public garages, must be installed in accordance with AN

Form 43206000 -4- Sept 2011 4.0) MINIMUM CLEARANCES TO COMBUSTIBLES Failure to do so may result in death, serious injury orproperty damage.Combustib

Form 43206000 Sept 2011 -5- 5.0) SPECIFICATIONS Model No.Model No.Model No.Model No. Btu/hrBtu/hrBtu/hrBtu/hr InInInInputputputput Orifice

Form 43206000 -6- Sept 2011 7.0) DIMENSIONS Top ViewBottom View18161-5/16exhaust outletperforatedpaneltube exchangerSide View36109-1/215-13/1

Form 43206000 Sept 2011 -7- 8.0) HEATER ASSEMBLY OVERVIEW 109-1/2suspension chain andturnbuckle rated @230lbsS hooks rated @ 115 lbslong axis of

Form 43206000 -8- Sept 2011 9.0) TYPICAL SUSPENSION METHODS All materials used to suspend the heater must have a minimum working loadof 115 lbs. All